想請問 , Malpensa 機場 到 Lainate 只能搭 taxi 嗎 ?
還有 , Lainate 有什麼必玩 ? 或 必吃的 ?
請您介紹囉 ! 謝謝 !

=======================================================================
ModelName:
===========
RT73(RT2571W) Wireless Lan Linux Driver

=======================================================================
Driver lName:
===========
rt73

=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.

=======================================================================
Description:
=============
This is a linux device driver for Ralink RT73 a/b/g WLAN Card.

=======================================================================
Contents:
=============
Makefile.4 : Makefile for kernel 2.4 series
Makefile.6 : Makefile for kernel 2.6 series
*.c : c files
*.h : header files

=======================================================================
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode
with open or shared or WPA-PSK or WPA2-PSK authentication method.
NONE, WEP, TKIP and AES encryption.

=======================================================================
Build Instructions:
====================

change the directory to be written!!!

1> $tar -xvzf RT73_Linux_STA_Drv_x.x.x.x.tar.gz
go to “./RT73_Linux_STA_Drv_x.x.x.x/Module” directory.

2> $cp Makefile.4 ./Makefile # [kernel 2.4]
or
$cp Makefile.6 ./Makefile # [kernel 2.6]

3> [kernel 2.4]
$chmod 755 Configure
$make config # config build linux os version

4> $make all # compile driver source code

5> $cp rt73.bin /etc/Wireless/RT73STA/ # copy firmware

6> $dos2unix rt73sta.dat
$cp rt73sta.dat /etc/Wireless/RT73STA/rt73sta.dat
# !!!check if it is a binary file before loading !!!

7> $load
#[kernel 2.4]
# $/sbin/insmod rt73.o
# $/sbin/ifconfig rausb0 inet YOUR_IP up

#[kernel 2.6]
# $/sbin/insmod rt73.ko
# $/sbin/ifconfig rausb0 inet YOUR_IP up

=======================================================================
CONFIGURATION:
====================
RT73 driver can be configured via following interfaces,
i.e. (i)”iwconfig” command, (ii)”iwpriv” command, (iii) configuration file
(iv)RaConfig

i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file “iwpriv_usage.txt” for details.
iii)copy configuration file “rt73sta.dat” to /etc/Wireless/RT73STA/rt73sta.dat.
iv) RaConfig is utility for rt73.

Note:

Configuration File : rt73sta.dat
—————————————
# Copy this file to /etc/Wireless/RT73STA/rt73sta.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use “vi -b rt73sta.dat” to modify settings according to your need.
#
# 1.) set NetworkType to “Adhoc” for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to “0″ for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be “WEPAUTO”, “OPEN”, “SHARED”, “WPAPSK”, “WPA2PSK”, “WPANONE”
# 5.) EncrypType can be “NONE”, “WEP”, “TKIP”, “AES”
# for more information refer to the Readme file.
#
# The word of “[Default]” must not be removed
[Default]
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WPAPSK=abcdefghijklmnopqrstuvwxyz
TxBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy=0;0;0;0
BGProtection=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0
AdhocOfdm=0
FastRoaming=0
RoamThreshold=70

———————————————–
syntax is ‘Param’='Value’ and describes below.

1. CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel

2. CountryRegionABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: use 52, 56, 60, 64 Channel
9: use 34, 38, 42, 46 Channel
10: use 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 Channel

3. SSID=value
value
0~z, 1~32 ascii characters.

4. WirelessMode=value
value
0: 11b/g mixed,
1: 11b only,
2: 11a only, //Support in RfIcType=1(id=RFIC_5226) or RfIcType=3(id=RFIC_5225)
3: 11a/b/g mixed, //Support in RfIcType=1(id=RFIC_5226) or RfIcType=3(id=RFIC_5225)
4: 11g only

5. TxRate=value
value
0: Auto //WirelessMode=0~4
1: 1 Mbps //WirelessMode=0 or 1 or 3
2: 2 Mbps //WirelessMode=0 or 1 or 3
3: 5.5 Mbps //WirelessMode=0 or 1 or 3
4: 11 Mbps //WirelessMode=0 or 1 or 3
5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4
6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4
7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4
8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4
9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4
10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4
11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4
12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4

6. Channel=value
value
depends on CountryRegion or CountryRegionABand

7. BGProtection=value
value
0: Auto
1: Always on
2: Always off

8. TxPreamble=value
value
0: Preamble Long
1: Preamble Short
2: Auto

9. RTSThreshold=value
value
1~2347

10. FragThreshold=value
value
256~2346

11. TxBurst=value
value
0: Disable
1: Enable

12. NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode

13. AdhocOfdm=value
value
0: WIFI mode (1,2,5.5,11 mbps rates)
1: b/g mixed, (1,2,5.5,11,6,9,12,18,24,36,48,54 mbps rates)
2: 11g only, (6,9,12,18,24,36,48,54 mbps rates)
3: 11a only, (6,9,12,18,24,36,48,54 mbps rates)

14. AuthMode=value
value
OPEN For open system
SHARED For shared key system
WEPAUTO Auto switch between OPEN and SHARED
WPAPSK For WPA pre-shared key (Infra)
WPA2PSK For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key (Adhoc)
WPA Use WPA-Supplicant
WPA2 Use WPA-Supplicant

15. EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK or WPANONE
AES For AuthMode=WPAPSK or WPA2PSK or WPANONE

16. DefaultKeyID=value
value
1~4

17. Key1=value
Key2=value
Key3=value
Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
(usage : “iwpriv” only)

18. Key1Type=vaule
Key2Type=value
Key3Type=vaule
Key4Type=vaule
value
0 hexadecimal type
1 assic type
(usage : reading profile only)

19. Key1Str=value
Key2Str=value
Key3Str=vaule
Key4Str=vaule
value
10 or 26 characters (key type=0)
5 or 13 characters (key type=1)
(usage : reading profile only)

20. WPAPSK=value
value
8~63 ASCII or
64 HEX characters

21. PSMode=value
value
0: CAM Constantly Awake Mode
1: Max_PSP Max Power Savings
2: Fast_PSP Power Save Mode

22. IEEE80211H=value
value
0: Disable
1: Enable Spectrum management
(This field can be enable only in A band)

23. FastRoaming=value
value
0: Disable
1: Enable Fast Roaming

24. RoamThreshold=value
vale
61 ~ 89

This value is a absolute threshold in dBm.
The condition to roam when receiving Rssi less than (-1*value).

// //////////////////////
// No Support !!!
// /////////////////////
// PktAggregate,
// TurboRate,
// WmmCapable,
// AckPolicy
// /////////////////////

MORE INFORMATION
=================================================================================
If you want for rt73 driver to auto-load at boot time:
A) choose rausb0 for first RT73 WLAN card, rausb1 for second RT73 WLAN card, etc.

B) create(edit) ‘ifcfg-rausb0′ file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias rausb0 rt73

C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-rausb0
DEVICE=’rausb0′
ONBOOT=’yes’

NOTE:
if you use dhcp, add this line too .
BOOTPROTO=’dhcp’

*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network

So I got confused in some instructions
which was written in “Read Me”

Here is the problem:
(I promise I’ve searched for the anwser with google for hours ,but in vain.)

The instruction in step6 to step7:
# !!!check if it is a binary file before loading!!!

I’ve checked rt73sta.dat,but it’s ASCII
code.I just can’t find the command which transfers the file to binary code the guidance requires.

The problem is urgent to me…
Please teach me step by step.

I will thank you to death.

I always get errors like “make[3]: *** [arparse.c] Error 1″ when I do ‘make’ at the ‘Install Simputils step.

Any idea?

Thanks in advance.